Listar Departament: Enginyeria de Sistemes Industrials i Disseny por fecha de publicación
-
Effect of the recycling and annealing on the mechanical and fracture properties of poly(lactic acid)
Springer US (2010)The aim of this work is to evaluate the use of Poly(lactic acid) (PLA) industrial waste as a source of raw material for certain applications, as well as to understand the effects of the annealing on the fracture behavior ... -
Influence of processing on the ethylene-vinyl alcohol (EVOH) properties: Application of the successive self-nucleation and annealing (SSA) technique
Budapest University of Technology (2010)Films of EVOH copolymers, processed three times by twin-screw extrusion were prepared using a cast-film line. The variation on the melt flow rate (MFR) and rheological behaviour of the films were determined, as well as the ... -
Taller de expresión tridimensional
Universitat Jaume I (2010)Este libro en formato PDF está basado en el temario armonizado de la asignatura Taller de modelos (510) y Taller de prototipos (521), pero también puede resultar útil para las asignaturas de Diseño del volumen (534), de ... -
The Effectiveness of Metaphoric Resources in Graphic Interface Design
Common Ground Publishing (2010)This research is conducted in a moment when the emergence of new formats in Communic- ation Technologies fills a gap in an unpublished stage on the social, cultural and artistic practices. The information access and its ... -
Automatización industrial
Universitat Jaume I (2010) -
Procesado del ácido poliláctico (PLA) y de nanocompuestos PLA/montmorillonita en planta piloto: Estudio de sus cambios estructurales y de su estabilidad térmica
Asociación de Químicos e Ingenieros del Instituto Químico de Sarrià (2010)Se aplican procesos de transformación y tratamiento de termoplásticos (inyección, extrusión-inyección y recocido) al ácido poliláctico (PLA) y a determinados nanocompues- tos PLA/montmorillonita, con objeto de estudiar las ... -
Improved Shunt Active Power Compensator for IEEE Standard 1459 Compliance
IEEE (2010)This paper presents the simulated and experimental results of an improved shunt active power compensator (SAPC). The proposed power compensator achieves IEEE Standard 1459 compliance by using moving-window discrete Fourier ... -
New Resolution of the Unbalance Power According to Std. 1459
IEEE (2010)Harmonic distortion and load unbalances have been an important issue in the last few years, motivating a large number of studies in active power compensators used for the power network quality improvement. Following an ... -
Tuning of PID Controllers based on simplified single parameter optimization
Taylor & Francis (2010)A simple method to design PID controllers in the frequency domain based on a simplified constrained optimiza- tion is proposed. The method is based on the use of a single tuning parameter, defined as the quotient between ... -
Aplicación de la mecánica de la fractura post-cedencia a polímeros
Universidad Simón Bolívar (2010)The Essential Work of Fracture (EWF) technique has been used for the ductile materials characterization, where yielding phenomenon occurs before crack propagation. The EWF method characterizes the post-yielding ... -
Guaranteed cost control analysis and iterative design for constrained Takagi-Sugeno systems
Elsevier (2010)This paper presents a novel control design technique in order to obtain a guaranteed cost fuzzy controller subject to constraints on the input channel. This guaranteed cost control law is obtained via multi-parametric ... -
Cutting parameters optimisation in milling: expert machinist knowledge versus soft computing method
Inderscience (2010)In traditional machining operations, cutting parameters are usually selected prior to machining according to machining handbooks and user’s experience. However, this method tends to be conservative and sub-optimal since ... -
A review of artificial intelligent approaches applied to part accuracy prediction
Inderscience (2010)Nowadays, despite the large volume of worldwide academic research on various aspects of metal cutting the control of workpiece precision still relies on machine-tool operator's experience and trial and error runs. In order ... -
Comparative study of nanocomposites of polyolefin compatibilizers containing kaolinite and montmorillonite organoclays
Wiley (2010-02)This work studied the morphology and physical properties of nanocomposites of different ethylene copolymers and functionalized polyethylenes with two different types of organoclays, to assess the potential application of ... -
Oxidation behaviour at 1123 K of AISI 304-Ni/Al-Al2O3/TiO2 multilayer system deposited by flame spray
Consejo Superior de Investigaciones Científicas (2011)The oxidation behaviour of alumina/titania (97/3, 87/13 and 60/40) ceramic coatings using a Ni-Al coupling layer was studied in a thermobalance. Both layers were deposited on an AISI 304 stainless steel base metal by the ... -
Universal design and visual impairment: tactile products for heritage access
Design Society (2011)This article presents a pilot study carried out in the city of Barcelona on assistive resources applied to an itinerary of possible interest to visually impaired people. The objective of this study was to use qualitative ... -
Fundamentos del modelado y prototipado virtual en el diseño de productos
Universitat Jaume I (2011) -
Similar model reference adaptive control with bounded control effort
John Wiley & Sons (2011)In this article, we propose an indirect similar model reference adaptive control scheme (SMRAC) in which the reference model is no longer constrained to be fixed but may be time varying in order to assure a bounded control ... -
Non-fundamental effective apparent power defined through an instantaneous power approach
Elsevier (2011)This paper proposes a new definition of non-fundamental effective apparent power based on an analysis of instantaneous power flows. This new instantaneous power approach for the calculation of the non-fundamental effective ... -
PI and PID auto-tuning procedure based on simplified single parameter optimization
Elsevier (2011)In this paper a new auto-tuning algorithm for PI and PID controllers based on relay experiments is proposed to minimize the load disturbance integral error (IE) by maximizing the integral gain, subject to a desired phase ...