Listar ESID_Articles por título
-
Design of a machine to rectify ceramic tiles for laboratory tests
IOP Publishing (2021)The tile rectification process, also called squaring, consists of machining the edges of the tile to make them straight, parallel two by two and perpendicular to the other two in addition to controlling the size of the ... -
Design of multi-station manufacturing processes by integrating the stream-of-variation model and shop-floor data
Elsevier (2011-04)Processdesign has been intensively studied to reduce dimensional variability of products produced in multi-stationmanufacturingprocesses (MMPs). Most of the existing studies focus on predicting variation propagation and ... -
Design of nanostructured siloxane-gelatin coatings: Immobilization strategies and dissolution properties
Elsevier (2018-02)Owing to the outstanding service life of metallic prostheses, a substantial effort has been put into their surface modification to improve biocompatibility and reduce metallic ion diffusion. To satisfy these requirements, ... -
Detailed study of DFIG-based wind turbines to overcome the most severe grid faults
Elsevier (2014-11)This paper studies the effects of voltage sags caused by faults on doubly-fed induction generators to overcome grid faults. A wide range of sag duration and depth values is considered. It is observed that sag duration ... -
Determination of the thermoelectric properties of a skutterudite-based device at practical operating temperatures by impedance spectroscopy
Elsevier (2019-10-01)Skutterudite-based thermoelectric materials are promising candidates for waste heat recovery applications at intermediate temperatures (300–500 °C) owing to their high dimensionless figure of merit and power factor. Recently, ... -
Determination of thermal conductivity, thermal diffusivity, and specific heat of liquids using a thermoelectric module
IOP Publishing (2024)Managing heat through working fluids is essential in many applications, as well as the development of new fluids with improved properties. Therefore, the characterization of their thermal properties, which is usually a ... -
Development and characterisation of strontium-doped sol-gel coatings to optimise the initial bone regeneration processes
Elsevier (2022)Strontium plays an important role in bone regeneration; it promotes the differentiation and maturation of osteoblasts and inhibits the activity of osteoclasts. Our principal objective in this study was to formulate new ... -
Development and Characterization of Electrospun Biopapers of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Derived from Cheese Whey with Varying 3-Hydroxyvalerate Contents
American Chemical Society (2021-06-16)In the present study, three different newly developed copolymers of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) with 20, 40, and 60 mol % contents in 3-hydroxyvalerate (3HV) were produced by the biotechnological ... -
Development and Characterization of Electrospun Fiber-Based Poly(ethylene-co-vinyl Alcohol) Films of Application Interest as High-Gas-Barrier Interlayers in Food Packaging
Multidisciplinary Digital Publishing Institute (2021-07-01)In the present study, poly(ethylene-co-vinyl alcohol) with 44 mol % ethylene content(EVOH44) was managed to be processed, for the first time, by electrospinning assisted by the coaxialtechnology of solvent jacket. In ... -
Development and characterization of electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) biopapers containing cerium oxide nanoparticles for active food packaging applications
MDPI (2023-02-23)Food quality is mainly affected by oxygen through oxidative reactions and the proliferation of microorganisms, generating changes in its taste, odor, and color. The work presented here describes the generation and further ... -
Development and characterization of fully renewable and biodegradable polyhydroxyalkanoate blends with improved thermoformability
MDPI (2022-06-21)Poly(3-hydroxybutyrate-co-3-valerate) (PHBV), being one of the most studied and commercially available polyhydroxyalkanoates (PHAs), presents an intrinsic brittleness and narrow processing window that currently hinders its ... -
Development and characterization of unmodified kaolinite/EVOH nanocomposites by melt compounding
Elsevier (2016-10)Nanocomposites of unmodified kaolinite (Kaol)/ethylene-vinyl alcohol copolymer (EVOH) with different Kaol contents have been obtained by a two-step process: melt blending in an internal mixer and film processing by ... -
Development of Active Barrier Multilayer Films Based on Electrospun Antimicrobial Hot-Tack Food Waste Derived Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and Cellulose Nanocrystal Interlayers
MDPI (2020)Active multilayer films based on polyhydroxyalkanoates (PHAs) with and without high barrier coatings of cellulose nanocrystals (CNCs) were herein successfully developed. To this end, an electrospun antimicrobial hot-tack ... -
Development of ciprofloxacin-loaded electrospun yarns of application interest as antimicrobial surgical suture materials
MDPI (2024-02-03)Surgical site infections (SSI) occur very frequently during post-operative procedures and are often treated with oral antibiotics, which may cause some side effects. This type of infection could be avoided by encapsulating ... -
Development of electrospun active films of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) by the incorporation of cyclodextrin inclusion complexes containing oregano essential oil.
Elsevier (2020-11)This paper reports the development of biodegradable active packaging films of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) by the incorporation of alpha- and gamma-cyclodextrins (-CD and-CDs) containing oregano ... -
Development of Electrospun Poly(3-hydroxybutyrate-co-3- hydroxyvalerate) Monolayers Containing Eugenol and Their Application in Multilayer Antimicrobial Food Packaging
Frontiers Media (2020-09-03)In this research, different contents of eugenol in the 2.5–25 wt.% range were first incorporated into ultrathin fibers of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) by electrospinning and then subjected to ... -
Discapacidad visual y orientación urbana. Estudio piloto sobre planos táctiles producidos en Impresión 3D
Fundación Infancia y Aprendizaje (2012-05-01)El trabajo aquí expuesto presenta un estudio piloto llevado a cabo en Barcelona con personas invidentes y deficientes visuales. El objetivo del mismo ha sido analizar el uso y la eficacia de los planos táctiles producidos ... -
Discussion on Useless Active and Reactive Powers Contained in the IEEE Standard 1459
IEEE (2011)This paper deals with the useless active powers and the reactive powers included in the unbalance power (SU1), and in the nonfundamental effective apparent power (SeN) defined in IEEE Standard 1459. Only the fundamental ... -
Diseño prospectivo y elementos de uso en parques urbanos a partir de la experiencia de las personas mayores
Resma (2009)Attention to the care and design of urban public spaces is a key factor when considering the quality of urban life. Parks and squares are spaces dedicated for everybody’s use and enjoyment, although some people, depending ... -
Diseño, producto y usuario: el papel del consumidor en el proceso de co-creación
Departamento de Dibujo. Facultad de Bellas Artes de Valencia. Universitat Poliècnica de València (2017)Este trabajo propone un nuevo modelo para el di - seño y desarrollo de nuevos productos y establece un marco de reflexión sobre la relación que debe establecer el diseñador con los consumidores ...