Buscar
Introducing an ionic conductive matrix to the cold-sintered Li1.3Al0.3Ti1.7(PO4)3-based composite solid electrolyte to enhance the electrical properties
(Elsevier, 2023-08-09)
In the present work, a Polymer-In-Ceramics (PIC) solid electrolyte based on Li1.3Al0.3Ti1.7(PO4)3 (LATP) and PEOn-LiTFSI (poly(ethylene oxide) - lithium bis(trifluoromethanesulfonyl)imide) is obtained via Cold Sintering ...
On the source inversion of fugitive surface layer releases. Part II. Complex sources
(Elsevier, 2017-06)
The experimental measurement of fugitive emissions of particulate matter entails inherent complexity because they are usually discontinuous, of short duration, may be mobile, and are affected by weather conditions. Owing ...
Clay hydration mechanisms and their effect on dustiness
(Elsevier, 2017-08)
Clays are employed in a wide variety of industries such as ceramic industry, manufacture of paper, rubber, etc. In this sense, it is well known that at industrial processes in which clayey materials are used, such as ceramic ...
Channeled PM10, PM2.5 and PM1 Emission Factors Associated with the Ceramic Process and Abatement Technologies
(MDPI, 2022-08-05)
A sampling methodology and a mathematical data treatment were developed that enable to determine not only total suspended particulates (TSP) emitted at channeled sources but also the PM10, PM2.5, and PM1 mass fractions ...
Improvement in Char Strength with an Open Cage Silsesquioxane Flame Retardant
(MDPI, 2017)
Different characterization techniques were used to study the hydrolysis and condensation
reaction kinetics of 3-methacryloxypropyltrimethoxysilane (MAPTMS) to obtain open cage
silsesquioxane oligomers. The formation of ...
Investigation of deformation behavior and fracture of ceramic coatings by the acoustic emission method
(Springer Verlag, 2017-03)
The use of protective coatings on components of machines and mechanisms provides the greatest economic benefit at the lowest additional cost. Plasma spraying is one of the most productive, technologically advanced, and ...
Improvement of the Electrochemical Behavior of (Sb, Sn, Cu)O Ceramic Electrodes as Electrochemical Advanced Oxidation Anodes
(Wiley, 2019-05-02)
This work explores the possibility of increasing the active surface of a Sb‐doped SnO2 ceramic electrode using CuO as sintering aid, by incorporating petroleum coke as a pore generator. In order to fulfil this goal, three ...
Stiffness variation of porous titanium developed using space holder method
(Maney on behalf of the Institute of Materials, Minerals and Nining, 2011-07)
The excellent properties of Ti have resulted in its generalised use for bone implants. However, Ti is very stiff in comparison with human cortical bone, and this creates problems of bone weakening and loosening of the ...
Ceria-doped scandia-stabilized zirconia (10Sc2O3·1CeO2·89ZrO2) as electrolyte for SOFCs: Sintering and ionic conductivity of thin, flat sheets
(WileyThe American Ceramic Society, 2017-03)
In this study, thin, flat sheets, about 90 μm thick, were prepared from ceria-doped scandia-stabilized zirconia with molecular formula 10Sc2O3·1CeO2·89 ZrO2 (10Sc1CeSZ) by tape casting and subsequent sintering at different ...
Bioactive glass suspensions preparation for suspension plasma spraying
(Elsevier, 2016-06)
A bioactive glass was dry-milled and sieved in order to obtain powders with particle size finer than 63 μm. Two suspensions, with different particle size distribution (D50 = 8.3 μm and D50 = 2.2 μm), were subsequently ...