Listar QUI_Articles por título
-
Foaming of flat glass cullet using Si3N4 and MnO2 powders
Elsevier (2009)The introduction of a compound capable of releasing oxygen, such as MnO2, greatly improves the foaming ability of Si3N4 used as foaming agent in soda-lime glass powder, leading to expansion at a relatively low temperature ... -
Fracture patterns of quartz particles in glass feldspar matrix
Elsevier (2012)We report a comparison between experimental evidences and simulation results of the micro cracking in ceramic materials provoked by the cooling process. The solid model and the fracture process are carried out using the ... -
Fracture properties of spray-dried powder compacts: Effect of granule size
Elsevier (2008)Inappropriate mechanical properties of spray-dried powder compacts lead to significant green product losses, entailing considerable costs in ceramic tile manufacture as well as serious environmental problems. In addition, ... -
Fracture toughness and temperature dependence of Young's modulus of a sintered albite glass
Elsevier (2013-03)Albite glass is an important component in many ceramic compositions, often used as liquid phase during the sintering process. Nevertheless, in spite of its almost ubiquous presence in the final microstructure of these ... -
Fuel effect on solution combustion synthesis of Co(Cr,Al)2O4 pigments
Elsevier (2017-10)The fuel effect on the synthesis of a ceramic pigment with a composition CoCr2−2ΨAl2ΨO4 (0 ≤ Ψ ≤ 1) by means of solution combustion synthesis process (SCS) has been studied. Three different fuels were selected to carry out ... -
Green strength testing of pressed compacts: An analysis of the different methods
Elsevier (2008)This paper presents a comparative study of three- and four-point bending tests and diametral compression (DC) tests, used to measure the mechanical strength of green pressed compacts. The study has been conducted on pressed ... -
Hardness and Young's modulus distributions in atmospheric plasmas prayed WC–Co coatings using nanoindentation
Elsevier (2011-05-25)A statistical indentation analysis of WC–Co coatings obtained by atmospheric plasma spray (APS) with two secondary plasma gases, H2 and He, was investigated using an instrumented indentation technique with the aim of ... -
Health risk assessment from exposure to particles during packing in working environments
Elsevier (2019-06-25)Packing of raw materials in work environments is a known source of potential health impacts (respiratory, cardiovascular) due to exposure to airborne particles. This activity was selected to test different exposure and ... -
Impact of Feedstock Nature on Thermal Conductivity of YSZ Thermal Barrier Coatings Obtained by Plasma Spraying
Göller Verlag GmbH (2016-09)Yttria-stabilized zirconia (YSZ) coatings with low thermal conductivity were obtained using three different particle size distributions as starting powder: nano-, submicron- and bimodal submicron/nano-sized particles. On ... -
Impact of fugitive emissions in ambient PM levels and composition. A case study in Southeast Spain
Elsevier (2010)The results of this study show the high impact that anthropogenic fugitive emissions of mineral dust have on air quality (levels of PM<sub>10</sub>, PM<sub>2.5</sub> and some metals) in a region in SE Spain named L'Alacantí. ... -
Impactos ambientales del ciclo de vida de las baldosas cerámicas. Análisis sectorial, identificación de estrategias de mejora y comunicación (II)
Reed Business Information (2011)El artículo analiza el potencial impacto ambiental que generan las baldosas cerámicas mediante un Análisis de Ciclo de Vida (ACV) a nivel sectorial, en el que participaron más de 50 empresas españolas. Los resultados han ... -
Impactos ambientales del ciclo de vida de las baldosas cerámicas: análisis sectorial, identificación de estrategias de mejora y comunicación (I)
Reed Business Information (2011)El artículo analiza el impacto ambiental que generan las baldosas cerámicas mediante el Análisis de Ciclo de Vida (AC) a nivel sectorial en el que participaron más de 50 empresas españolas. Los resultados han servido ... -
Improvement in Char Strength with an Open Cage Silsesquioxane Flame Retardant
MDPI (2017)Different characterization techniques were used to study the hydrolysis and condensation reaction kinetics of 3-methacryloxypropyltrimethoxysilane (MAPTMS) to obtain open cage silsesquioxane oligomers. The formation of ... -
Improvement of salicylic acid biological effect through its encapsulation with silica or chitosan
Elsevier B.V. (2021-12-30)Attacks of necrotrophic and biotrophic fungi affect a large number of crops worldwide and are difficult to control with fungicides due to their genetic plasticity. Encapsulation technology is a good alternative for ... -
Improvement of the Electrochemical Behavior of (Sb, Sn, Cu)O Ceramic Electrodes as Electrochemical Advanced Oxidation Anodes
Wiley (2019-05-02)This work explores the possibility of increasing the active surface of a Sb‐doped SnO2 ceramic electrode using CuO as sintering aid, by incorporating petroleum coke as a pore generator. In order to fulfil this goal, three ... -
Improvement of the mechanical and aesthetic properties of a coating by inkjet technology
Wiley (2021-01-11)Different amounts of ink, made up almost entirely of a frit that devitrified abundant small crystals of anorthoclase, were applied by inkjet printing onto a traditional unfired glaze substrate. The rheological properties ... -
In operando characterization of the ionic conductivity dependence on liquid transient phase and microstructure of cold-sintered Bi2O3-doped Li1.3Al0.3Ti1.7(PO4)3 solid-state electrolyte
Elsevier (2023-08-31)A disruptive sintering technique, Cold Sintering Process (CSP), has been used to produce cold-sintered samples of Bi2O3-doped Li1.3Al0.3Ti1.7(PO4)3 (LATP) as solid-state electrolyte (SSE). An in operando impedance study ... -
In vitro study of bioactive glass coatings obtained by atmospheric plasma spraying
Elsevier (2022-02)This research has addressed a complete study of the bioactivity of bioactive glass coatings obtained by atmospheric plasma spraying. The coatings have been characterized in terms of microstructure, adhesion, crystalline ... -
In vitro toxicity of industrially relevant engineered nanoparticles in human alveolar epithelial cells: air–liquid interface versus submerged cultures
MDPI (2021-11-27)Diverse industries have already incorporated within their production processes engineered nanoparticles (ENP), increasing the potential risk of worker inhalation exposure. In vitro models have been widely used to investigate ... -
Industry-scalable wall tile composition based on circular economy
Sociedad Española de Cerámica y Vidrio (2022-08)En el marco de la economía circular y la valorización de residuos, el presente trabajo aborda la posibilidad de fabricar azulejos cuyos soportes incluyan residuos en su formulación. Los residuos seleccionados son tiesto ...