Listar EMC_Articles por título
-
Damage Detection Using Ultrasonic Techniques in Concrete-Filled Steel Tubes (CFSTs) Columns
MDPI (2022)Concrete-filled steel tubes (CFSTs) are structural elements that, as a consequence of an incorrect elaboration, can exhibit internal defects that cannot be visualized, being usually air voids. In this work, the detection ... -
Dataset of Tactile Signatures of the Human Right Hand in Twenty-One Activities of Daily Living Using a High Spatial Resolution Pressure Sensor
MDPI (2021)Successful grasping with multi-fingered prosthetic or robotic hands remains a challenge to be solved for the effective use of these hands in unstructured environments. To this end, currently available tactile sensors need ... -
Declaraciones Ambientales según ISO 14025 en el sector de la construcción. Parte 1: Marco normativo y metodología
Publica (2013)Este artículo se centra en las Declaraciones Ambientales reguladas por la norma ISO 14025 (2006) en el sector de la construcción. -
Declaraciones Ambientales según ISO14025 en el sector de la construcción. Parte 2: Recubrimientos cerámicos
Publica (2013)Este artículo tiene como finalidad aportar información relativa a los Programas, tanto generales como sectoriales, que han desarrollado Reglas de Categoría de Producto (RCP) para diferentes tipos de recubrimientos cerámicos, ... -
Declaración ambiental según ISO 14025: una oportunidad para informar de los aspectos ambientales de los servicios de gestión de residuos
Reed Business Information (2009)Type III Environmental Declarations as set out by standard UNE-ISO 14025 (2007) are a voluntary instrument that organizations can use to foster the demand for and supply of systems that have a lower impact on the ... -
Desarrollo de un método multibloque para la generación automatizada de mallas tridimensionales de engranajes
Fundación Técnica Industrial (2022-04)En este trabajo se presenta un nuevo método para la generación automatizada de mallas tridimensionales de engranajes. Para ello, se siguen los pasos característicos de un método de mallado multibloque para generar una malla ... -
Design and optimization of a semi‐industrial cavitation device for a pretreatment of an anaerobic digestion treatment of excess sludge and pig slurry
Wiley (2020)The use of hydrodynamic cavitation (HC) as a wastewater treatment and anaerobic digestion pretreatment is a well‐known process. However, most of the experiments have been done at laboratory scale and using a low concentration ... -
Design of a model to assess the environmental risk of leachate dams
Elsevier (2008)Leachate dams store very toxic liquids, leachate, that contain a large amount of pollutant substances. Most of them are located in gullies or ravines, so if a dam breaks, leachate would advance downstream provoking an ... -
Design of a Municipal Solid Waste Collection System in Situations with a Lack of Resources: Nikki (Benin), a Case in Africa
MDPI (2021)Waste collection is one of the most important public services in a town. However, waste collection has not been effectively implemented in some places due to the lack of economic and management resources. The waste is ... -
Design of an environmentally friendly refrigeration laboratory based on cooling capacity calculation for graduate students
Ahmad Ibrahim (2018)Lower global warming potential (GWP) refrigerants must be used in refrigeration education to integrate the environmentally responsible engineering principles in class. However, most of the refrigeration educational ... -
Design of Virtual Hands for Natural Interaction in the Metaverse
MDPI (2024)The emergence of the Metaverse is raising important questions in the field of human–machine interaction that must be addressed for a successful implementation of the new paradigm. Therefore, the exploration and integration ... -
Design, tuning and in-field validation of energy harvesters for railway bridges
Elsevier (2024)Energy harvesters are a promising technology for powering infrastructure condition monitoring systems without batteries. When deployed on railway bridges they are typically tuned to the bridge’s natural frequency, however ... -
Detección de defectos en carrocerías de vehículos basado en visión artificial: diseño e implantación
Elservier (2012-01)This paper describes the design and implementation of a novel inspection system for detecting defects on car bodies based on artificial vision, implemented in Ford Factory at Almussafes (Spain). The system is based on the ... -
Determination of mercury distribution inside spent compact fluorescent lamps by atomic absorption spectrometry
Elsevier (2012-05)In this study, spent compact fluorescent lamps were characterized to determine the distribution of mercury. The procedure used in this research allowed mercury to be extracted in the vapor phase, from the phosphor powder, ... -
Determination of the ISO face load factor in spur gear drives by the finite element modeling of gears and shafts
Elsevier (2013)The face load factor is a common coefficient used in gear design standards that takes into account the uneven distribution of load across the face width of the gears caused by the mesh misalignment. In this paper, a finite ... -
Development and validation of a finite element model for water – CO2 coaxial gas-coolers
Elsevier (2012-05)The gas-cooler heat exchanger is a characteristic device of the refrigeration plants that use CO2 as the working fluid in transcritical conditions. The proper gas-cooler sizing, allows getting the maximum effectiveness in ... -
Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids
Elsevier (2015)This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant ... -
Development and validation of a one-dimensional solver in a CFD platform for boiling flows in bubbly regimes
Elsevier (2021)This paper presents a new one-dimensional solver for two-phase flow simulations where boiling is involved. The solver has been implemented within the OpenFOAM® platform. The basic formulation follows the Eulerian description ... -
Development of a low-medium temperature T-history setup for the thermal storage characterization of non-homogeneous mixtures containing PCMs
Elsevier (2023-12-25)More attention has been paid to thermal energy storage in recent years for its advantages in heating and cooling applications to foster the use of renewable energies. As part of the design of new thermal energy storage ... -
Development of a multiblock procedure for automated generation of two-dimensional quadrilateral meshes of gear drives
Elsevier (2020)This article describes a new multiblock procedure for automated generation of two-dimensional quadrilateral meshes of gear drives. The typical steps of the multiblock schemes have been investigated in depth to obtain a ...