Listar Departament: Enginyeria Mecànica i Construcció por título
-
Damage Detection Using Ultrasonic Techniques in Concrete-Filled Steel Tubes (CFSTs) Columns
MDPI (2022)Concrete-filled steel tubes (CFSTs) are structural elements that, as a consequence of an incorrect elaboration, can exhibit internal defects that cannot be visualized, being usually air voids. In this work, the detection ... -
Dataset of Tactile Signatures of the Human Right Hand in Twenty-One Activities of Daily Living Using a High Spatial Resolution Pressure Sensor
MDPI (2021)Successful grasping with multi-fingered prosthetic or robotic hands remains a challenge to be solved for the effective use of these hands in unstructured environments. To this end, currently available tactile sensors need ... -
Declaraciones Ambientales según ISO 14025 en el sector de la construcción. Parte 1: Marco normativo y metodología
Publica (2013)Este artículo se centra en las Declaraciones Ambientales reguladas por la norma ISO 14025 (2006) en el sector de la construcción. -
Declaraciones Ambientales según ISO14025 en el sector de la construcción. Parte 2: Recubrimientos cerámicos
Publica (2013)Este artículo tiene como finalidad aportar información relativa a los Programas, tanto generales como sectoriales, que han desarrollado Reglas de Categoría de Producto (RCP) para diferentes tipos de recubrimientos cerámicos, ... -
Declaración ambiental según ISO 14025: una oportunidad para informar de los aspectos ambientales de los servicios de gestión de residuos
Reed Business Information (2009)Type III Environmental Declarations as set out by standard UNE-ISO 14025 (2007) are a voluntary instrument that organizations can use to foster the demand for and supply of systems that have a lower impact on the ... -
Definición de una arquitectura para la asistencia en el diseño de productos
Asociación Española de Dirección e Ingeniería de Proyectos (AEIPRO) (2002)This paper reports an ongoing research project aimed to develop a new Knowledge Based Engineering (KBE) system to support product design. Current knowledge modelling capabilities of KBE are considered and enhancements ... -
Depuración de aguas residuales: digestión anaerobia
Publicacions de la Universitat Jaume I, (2018)La càtedra universitat-empresa FACSA d'Innovació en el Cicle Integral de l'Aigua de la Universitat Jaume I té com a objectiu fomentar l'intercanvi d'idees, la transferència de coneixement i la trobada entre tots els actors ... -
Desarrollo de un método multibloque para la generación automatizada de mallas tridimensionales de engranajes
Fundación Técnica Industrial (2022-04)En este trabajo se presenta un nuevo método para la generación automatizada de mallas tridimensionales de engranajes. Para ello, se siguen los pasos característicos de un método de mallado multibloque para generar una malla ... -
Desarrollo de una herramienta gráfica para el ecodiseño de productos
Asociación Española de Dirección e Ingeniería de Proyectos (AEIPRO) (2014-01-31)Durante los últimos años se ha producido un gran avance en la concienciación ambiental de los consumidores y en el conocimiento de los perjuicios ambientales que producen los productos industriales. El diseñador juega ... -
Desconexión entre la normativa vigente aplicable y las aulas en las titulaciones de grado. Estudio introductorio en dos universidades españolas
Autoeditado por Comité Congreso (2019)El cambio climático es una realidad y se debe concienciar a la sociedad desde todos los estamentos educativos con medidas eficaces para mitigar sus efectos. Desde el punto de vista de la ingeniería, los sistemas de ... -
Design and optimization of a semi‐industrial cavitation device for a pretreatment of an anaerobic digestion treatment of excess sludge and pig slurry
Wiley (2020)The use of hydrodynamic cavitation (HC) as a wastewater treatment and anaerobic digestion pretreatment is a well‐known process. However, most of the experiments have been done at laboratory scale and using a low concentration ... -
Design issues concerning circular economy assessment methods at the product level: a comparative analysis through a case study of a mobile tiny house
Cambridge University Press (2024-06-05)Sustainability evaluations are increasingly relevant in the design of products. Within sustainability-related frameworks, circular economy (CE) has gained attention in the last few years, and this has vastly affected design, ... -
Design of a capsule coffee machine integrating principles of reparability
Asociación Española de Dirección e Ingeniería de Proyectos (AEIPRO) (2023-07-10)The "New Action Plan for the circular economy" presented by the European Commission promotes the sustainable and circular design of products, promoting their durability, reuse, updating and repairability, as strategies to ... -
Design of a model to assess the environmental risk of leachate dams
Elsevier (2008)Leachate dams store very toxic liquids, leachate, that contain a large amount of pollutant substances. Most of them are located in gullies or ravines, so if a dam breaks, leachate would advance downstream provoking an ... -
Design of a Municipal Solid Waste Collection System in Situations with a Lack of Resources: Nikki (Benin), a Case in Africa
MDPI (2021)Waste collection is one of the most important public services in a town. However, waste collection has not been effectively implemented in some places due to the lack of economic and management resources. The waste is ... -
Design of an environmentally friendly refrigeration laboratory based on cooling capacity calculation for graduate students
Ahmad Ibrahim (2018)Lower global warming potential (GWP) refrigerants must be used in refrigeration education to integrate the environmentally responsible engineering principles in class. However, most of the refrigeration educational ... -
Design of solid recovered fuels from municipal solid waste and biomass
Asociación Española de Dirección e Ingeniería de Proyectos (AEIPRO) (2020-07-07)The solid recovered fuels (SRF) are a viable alternative to the conventional fossil fuels which can be partially replaced at heat and electricity industries. Additionally, as they have a percentage of biomass, they have ... -
Design of Virtual Hands for Natural Interaction in the Metaverse
MDPI (2024)The emergence of the Metaverse is raising important questions in the field of human–machine interaction that must be addressed for a successful implementation of the new paradigm. Therefore, the exploration and integration ... -
Design, tuning and in-field validation of energy harvesters for railway bridges
Elsevier (2024)Energy harvesters are a promising technology for powering infrastructure condition monitoring systems without batteries. When deployed on railway bridges they are typically tuned to the bridge’s natural frequency, however ... -
Detección de defectos en carrocerías de vehículos basado en visión artificial: diseño e implantación
Elservier (2012-01)This paper describes the design and implementation of a novel inspection system for detecting defects on car bodies based on artificial vision, implemented in Ford Factory at Almussafes (Spain). The system is based on the ...