Determinants of workplace exposure and release of ultrafine particles during atmospheric plasma spraying in the ceramic industry
Ver/ Abrir
Impacto
Scholar |
Otros documentos de la autoría: Viana, Marcelo; Fonseca, A.S.; Querol, Xavier; López Lilao, Ana; Carpio Cobo, Pablo; Salmatonidis, Apostolos; Monfort, Eliseo
Metadatos
Mostrar el registro completo del ítemcomunitat-uji-handle:10234/9
comunitat-uji-handle2:10234/7033
comunitat-uji-handle3:10234/8618
comunitat-uji-handle4:
INVESTIGACIONMetadatos
Título
Determinants of workplace exposure and release of ultrafine particles during atmospheric plasma spraying in the ceramic industryAutoría
Fecha de publicación
2017Editor
ElsevierISSN
0048-9697; 1879-1026Cita bibliográfica
Viana, M., Fonseca, A. S., Querol, X., López-Lilao, A., Carpio, P., Salmatonidis, A., & Monfort, E. (2017). Workplace exposure and release of ultrafine particles during atmospheric plasma spraying in the ceramic industry. Science of The Total Environment, 599, 2065-2073.Tipo de documento
info:eu-repo/semantics/articleVersión de la editorial
http://www.sciencedirect.com/science/article/pii/S0048969717312329?via%3DihubVersión
info:eu-repo/semantics/submittedVersionPalabras clave / Materias
Resumen
Atmospheric plasma spraying (APS) is a frequently used technique to produce
enhanced-property coatings for different materials in the ceramic industry. This work
aimed to characterise and quantify the impact of APS ... [+]
Atmospheric plasma spraying (APS) is a frequently used technique to produce
enhanced-property coatings for different materials in the ceramic industry. This work
aimed to characterise and quantify the impact of APS on workplace exposure to
airborne particles, with a focus on ultrafine particles (UFPs, <100 nm) and
nanoparticles (<50 nm). Particle number, mass concentrations, alveolar lung deposited
surface area concentration, and size distributions, in the range 10 nm – 20 μm were
simultaneously monitored at the emission source, in the worker breathing zone, and in
outdoor air. Different input materials (known as feedstock) were tested: (a) micro-sized
powders, and (b) suspensions containing submicron- or nano-sized particles. Results
evidenced significant UFP emissions (up to 3.3x106/cm3) inside the projection
chamber, which impacted exposure in the breathing zone outside the projection
chamber (up to 8.3x105/cm3). Environmental release of UFPs was also detected and
quantified (3.9x105/cm330 ). Engineered nanoparticle (ENP) release to workplace air was
also evidenced by TEM microscopy. UFP emissions were detected during the
application of both micro-sized powder and suspensions containing submicron- or
nano-sized particles, thus suggesting that emissions were process- (and not material-)
dependent. An effective risk prevention protocol was implemented, which resulted in a
reduction of worker UFP exposure in the breathing zone. These findings evidence the
potential risk of occupational exposure to UFPs during atmospheric plasma spraying,
and raise the need for further research on UFP formation mechanisms in high-energy
industrial processes. [-]
Publicado en
Science of The Total Environment, 2017, vol. 599, p. 2065-2073.Proyecto de investigación
This project was supported by the Spanish MINECO through project PCIN-2015-173- C02-01, under the frame of SIINN, the ERA-NET for a Safe Implementation of Innovative Nanoscience and Nanotechnology, by SIINN-ERANET project CERASAFE (id.:16). Support is also acknowledged to FP7 Marie Curie ITN HEXACOMM (Nr. 315760), Generalitat de Catalunya 2014 SGR33, the Department of Environmental Quality of the Generalitat de Catalunya, and the Spanish Ministry of the Environment (13CAES006).Derechos de acceso
http://rightsstatements.org/vocab/CNE/1.0/
info:eu-repo/semantics/openAccess
info:eu-repo/semantics/openAccess
Aparece en las colecciones
- QUI_Articles [300]