Listar ESID_Articles por título
-
Experiencias inmersivas durante la fase conceptual del proyecto arquitectónico: la realidad virtual como herramienta para la participación del usuario en el proceso de co-creación
Asociación de profesores de expresión gráfica aplicada a la edificación (APEGA) (2018)La elevada competencia del mercado actual dificulta la contratación de proyectos singulares de viviendas unifamiliares. Por ello, resulta necesario agudizar el ingenio para ofrecer al cliente una ... -
Experimental conditions required for accurate measurements of electrical resistivity, thermal conductivity, and dimensionless figure of merit (ZT) using Harman and impedance spectroscopy methods
AIP Publishing (2019-01-11)The Harman method is used extensively for the characterization of the dimensionless figure of merit ZT of thermoelectric (TE) materials and devices. However, its accuracy has often been questioned, since in many cases there ... -
Experimental tuning of PI controllers with symmetric send-on-delta sampling from the step response
Taylor & Francis (2024-01-02)This paper proposes a technique for tuning PI controllers with symmetric send-on-delta (SSOD) sampling,using three measurements taken from the step response. The tuning procedure is based on a previouslypublished experimental ... -
Explicit Predictive Control with Non-Convex Polyhedral Constraints
Elsevier (2012-02)This paper proposes an explicit solution to the model predictive control of linear systems subject to non-convex polyhedral constraints. These constraints are modeled as the union of a finite number of convex polyhedra. ... -
Extension of the Stream-of-Variation Model for General-Purpose Workholding Devices: Vices and Three-Jaw Chucks
Institute of Electrical and Electronics Engineers (2021-03-23)Nowadays, advanced manufacturing models, such as the stream-of-variation (SoV) model, have been successfully applied to derive the complex relationships between fixturing, manufacturing, and datum errors throughout a ... -
Extensions to “Stability Analysis of Fuzzy Control Systems Subject to Uncertain Grades of Membership”
Institute of Electrical and Electronics Engineer (New York) (2008)In the December 2005 issue of this journal, Lam and Leung proposed stability results for fuzzy control systems where the membership functions in the controller were not the same as those from the process one, but some ... -
Fabrication and evaluation of a skutterudite-based thermoelectric module for high temperature applications
Springer (2013-07)We report a straightforward methodology for the fabrication of high-temperature thermoelectric (TE) modules using commercially available solder alloys and metal barriers. This methodology employs standard and accessible ... -
La fachada retablo de la Iglesia de Nuestra Señora de la Asunción de Vistabella del Maestrazgo (Castellón)
Universidad Politécnica de Valencia (2016)La fachada retablo de la iglesia de Nuestra Señora de la Asunción de Vistabella del Maestrazgo (Castellón), es uno de los elementos arquitectónicos más importantes del Renacimiento Valenciano. El objetivo de este ... -
Fault-tolerant strategies in MMC-based high power magnet supply for particle accelerator
Elsevier (2023)Many particle accelerators require to supply chains of magnets with high quality, high magnitude, cycling currents. To do this, the power converters need to provide high output voltages, reaching in some cases tens of ... -
Feature-Based Framework for Inspection Process Planning
MDPI (2018)Feature-based approaches have been profusely used in the last decades to incorporate domain-specific knowledge in the design and development of technical systems that, according to the new Concurrent Engineering approaches, ... -
Femtosecond laser micromachining with extended depth of focus by using diffractive lenses
Elsevier (2014-06-01)We show that a simple diffraction focusing element can alleviate mechanical tolerances in ultrafast laser microprocessing. In particular, we experimentally demonstrate that, in comparison with a conventional refractive ... -
Fostering in-process inspection during process planning using tolerance charting
Elsevier (2013)Integrated development of machining and inspection plans is essential in dynamic manufacturing environments, especially when right first time manufacturing is required. In this work, a methodology, based on a new and ... -
Fracture behavior of quenched poly(lactic acid)
BME-PT (2011)The effect of a quenching treatment applied on heated cast sheet extruded films of two poly(lactic acid) (PLA) commercial grades, with different optical purities, was studied. The thermal and mechanical properties of the ... -
Fracture behaviour of poly[ethylene–(vinyl alcohol)]/organo-clay composites
Wiley (2009)BACKGROUND: Ethylene–(vinyl alcohol) (EVOH) copolymer/organo‐modified montmorillonite (OMMT) composites were investigated. Composites with two different percentages by weight of OMMT were prepared using a melt‐extrusion ... -
Frequency-dependent approach to model validation for iterative identification and control schemes
Institution of Engineering and Technology (2009)Classical validation methods “accept” or “reject” a model as a valid representation of a plant for some intended use. However this binary result has several problems as firstly, models are neither good nor bad but have ... -
Fuzzy discretization and control for non-linear, multiple binary input systems
Elsevier (2023)The control of continuous-time linear systems with binary inputs cannot benefit from existing control design techniques because they are based on continuous control actions. In particular, optimal control problems with ... -
Generalized one-cycle current controller for improved SAPF power quality management
Elsevier Ltd (2024-06-01)Current controllers are used in shunt active power filters to enhance the performance of electrical power systems by improving power quality and energy efficiency. Nonlinear current controllers are preferred in systems ... -
Guaranteed cost control analysis and iterative design for constrained Takagi-Sugeno systems
Elsevier (2010)This paper presents a novel control design technique in order to obtain a guaranteed cost fuzzy controller subject to constraints on the input channel. This guaranteed cost control law is obtained via multi-parametric ... -
Guiding questions for increasing the generation of product ideas to meet changing needs (QuChaNe)
Springer (2021-03-23)One of the reasons why products are replaced is as a consequence of changes in the users’ personal life. Adaptable or upgradable products have the advantage that, to some extent, they counter dissatisfaction in products ... -
Harmonic Resonance Stability of Aeronautical Ground Lighting Systems
IEEE (2018-02)Aeronautical ground lighting (AGL) systems assist aircraft pilots in airport operations. These systems are singlephase series circuits where constant current regulators (CCRs) feed luminaires with an adjustable rms current. ...