Listar EMC_Articles por título
-
Potential reuse of small household waste electrical and electronic equipment: Methodology and case study
Elsevier (2016-03)This study proposes a general methodology for assessing and estimating the potential reuse of small waste electrical and electronic equipment (sWEEE), focusing on devices classified as domestic appliances. Specific tests ... -
Potential use of ceramic sanitary ware waste as pozzolanic material
Elsevier (2021)This paper evaluated the pozzolanic activity of ceramic sanitary ware (CSW) waste when blended with Portland cement (PC). CSW waste units were broken, crushed and milled to reduce their particle size. These particles were ... -
Power factor improvement in a solid–liquid thermoelectric system formed by Sb:SnO2 in contact with a chromium complex solution
Royal Society of Chemistry (2023)Thermoelectric (TE) materials can convert heat into electricity. Good TE materials should have high power factors (PF) and low thermal conductivities. PF = S2σ is governed by the Seebeck coefficient S and the electrical ... -
Pozzolanic activity of tiles, bricks and ceramic sanitary-ware in ecofriendly Portland blended cements
Elsevier (2020-08-26)Reusing ceramic waste as a pozzolanic admixture may offer environmental benefits as it allows the reduction in the consumption of natural resources and energy, and the reduction of CO2 emissions associated with Portland ... -
Predicting Wrist Joint Angles from the Kinematics of the Arm: Application to the Control of Upper Limb Prostheses
MDPI (2023-06)Automation of wrist rotations in upper limb prostheses allows simplification of the human–machine interface, reducing the user’s mental load and avoiding compensatory movements. This study explored the possibility of ... -
Prediction of Contact Angle of Nanofluids by Single-Phase Approaches
MDPI (2019)Wettability is the ability of the liquid to contact with the solid surface at the surrounding fluid and its degree is defined by contact angle (CA), which is calculated with balance between adhesive and cohesive forces ... -
Predictions of European refrigerants place on the market following F-gas regulation restrictions
Elsevier (2021-03-10)The European Union (EU) Regulation on fluorinated greenhouse gases (F-gases) has encouraged to reduce gradually the number of hydrofluorocarbons (HFC) that can be placed on the market (POM) to 21% of the baseline level in ... -
Predictive and Multi-rate Sensor-Based Planning under Uncertainty
Institute of Electrical and Electronics Engineers (IEEE) (2014-12-08)Email Print Request Permissions In this paper, a general formulation of a predictive and multirate (MR) reactive planning method for intelligent vehicles (IVs) is introduced. The method handles path planning and trajectory ... -
Preliminary Study of the Fresh and Hard Properties of UHPC That Is Used to Produce 3D Printed Mortar
MDPI (2022-04-04)Three-dimensional printed concrete (3DPC) is a relatively recent technology that may be very important in changing the traditional construction industry. The principal advantages of its use are more rapid construction, ... -
Preliminary study on the fresh and mechanical properties of UHPC made with recycled UHPC aggregates
Taylor & Francis (2021-11-09)The recycling of construction and demolition waste material reduces disposal of material and also the consumption of resources, therefore promoting sustainability in construction. Ultra-high performance concrete (UHPC) is ... -
Premolars restored with posts of different materials: fatigue analysis
The Japanese Society for Dental Materials and Devices (2011-11-30)Previous works studied the effect of the material and the dimensions of the post on the biomechanical performance (fracture strength and stress distribution) of restored teeth, under static loads. The aim of this work was ... -
Principles of Affective Design in Consumers’ Response to Sustainability Design Strategies
MDPI (2020)The aim of this paper is to explore the generation of consumers’ responses to sustainabilitydesign strategies by considering the principles of affective design. A conceptual model of consumers’response, in which a distinction ... -
Prioritising organisational circular economy strategies by applying the partial order set theory: Tool and case study
Elsevier (2023)This study presents a methodology to solve circular economy multiple indicators system decision-making problems by applying the Partial Order Set Theory (POSET). To this end, a user-friendly tool was developed to allow the ... -
Problems Using Data Gloves with Strain Gauges to Measure Distal Interphalangeal Joints’ Kinematics
MDPI (2022)Data gloves with strain gauges are a widely used technology to record hand kinematics. Several researchers have experienced problems when using data glove models to record distal interphalangeal (DIP) joints, mainly in ... -
Procedure for evaluating and refurbishing envelopes of obsolete buildings in warm regions
Taylor & Francis (2016)This research develops a procedure to evaluate and refurbish obsolete buildings obliged to comply with the Spanish Technical Building Code. This procedure matches the building typologies selected to the optimal solution ... -
El proceso de secado por atomización: formación de gránulos y cinética de secado de gotas
Sociedad Española de Cerámica y Vídrio (2013-07)Spray drying is a unit operation very common in many industrial processes. For each particular application, the resulting granulated material must possess determined properties that depend on the conditions in which the ... -
Producción y caracterización del CSR procedente del rechazo de una planta de recuperación y compostaje
Informanews Iberia S. A. (2010)La valorización energética constituye una de las alternativas para la gestión de los rechazos de las plantas de tratamiento de residuos, ya que se trata de un material que no se puede reciclar, ni compostar ni biometanizar. ... -
Product Data Quality and Collaborative Engineering
IEEE Computer Society (2002-05)n this article, the authors analyze the impact of product data quality in the implementation of collaborative engineering in an extended enterprise framework. They also analyze the product data model as a key element for ... -
Programación y compromiso. Cómo equilibrar dos objetivos, económico y ambiental, en una promoción de viviendas
Asociación Española de Economía Agraria, AEEA (2015)En la construcción de edificios entran en conflicto el objetivo económico para el usuario y el objetivo ambiental para la sociedad. La aplicación de la metodología multiobjetivo y programación compromiso puede ser útil ... -
Properties and microstructure of alkali-activated red clay brick waste
Elsevier (2013-06)Sintered red clay ceramic is used to produce hollow bricks which are manufactured in enormous quantities in Spain. They also constitute a major fraction of construction and demolition waste. The aim of this research was ...