Listar Departament: Enginyeria de Sistemes Industrials i Disseny por idioma "eng"
-
A review of machining monitoring systems based on artificial intelligence process models
Springer-Verlag (2009)Many machining monitoring systems based on artificial intelligence (AI) process models have been successfully developed in the past for optimising, predicting or controlling machining processes. In general, these monitoring ... -
A Review of the Factors Influencing Surface Roughness in Machining and Their Impact on Sustainability
MDPI (2024)Understanding surface roughness generation in machining is critical to estimate the final quality of the part, optimize cutting conditions, reduce costs and improve manufacturing sustainability in industry. This work ... -
A Sequential Inspection Procedure for Fault Detection in Multistage Manufacturing Processes
MDPI (2021)Fault diagnosis in multistage manufacturing processes (MMPs) is a challenging task where most of the research presented in the literature considers a predefined inspection scheme to identify the sources of variation and ... -
A simple procedure for fault detectors design in SISO systems
Elsevier (2020-03)In this work, we present a novel approach for fault detectors design and implementation in the case of actuator faults. Both the design and the implementation are focused on simplicity. The fault detector is based in an ... -
A single coating with antibacterial properties for prevention of medical device-associated infections
Elsevier (2019-04)Human bacterial pathogens found on medical implants are one of the main causes of morbidity and mortality, making the development of novel coatings the primary strategy in the prevention of medical device-associated ... -
A Tool Condition Monitoring System Based on Low-Cost Sensors and an IoT Platform for Rapid Deployment
MDPI (2023)Tool condition monitoring (TCM) systems are key technologies for ensuring machining efficiency. Despite the large number of TCM solutions, these systems have not been implemented in industry, especially in small- and ... -
A Triangulation Approach to Asymptotically Exact Conditions for Fuzzy Summations
Institute of Electrical and Electronics Engineers (IEEE) (2009)Many Takagi-Sugeno (T-S) fuzzy control-synthesis problems in the literature are expressed as the problem of finding decision variables in a double convex sum (fuzzy summation) of positive definite matrices. Matricespsila ... -
Accelerated Discovery of Thermoelectric Materials: Combinatorial Facility and High-Throughput Measurement of Thermoelectric Power Factor
American Chemical Society (2016-05)A series of processes have been developed to facilitate the rapid discovery of new promising thermoelectric alloys. A novel combinatorial facility where elements are wire-fed and laser-melted was designed and constructed. ... -
Accuracy of a single position estimate for kNN-based fingerprinting indoor positioning applying error propagation theory
IEEE (2023-06-23)Indoor Positioning Systems usually consider the average positioning error over a set of evaluation samples, or a quartile of that value, as the global error. However, they do not provide a metric for the uncertainty for ... -
Acquisition of transversal skills through PBL: a study of the perceptions of the students and teachers in materials science courses in engineering
Universitat Politècnica de València (2015)The main goal of this work is describing the experience in using Project Based Learning (PBL) methodology in Materials Science courses in several Engineering degrees. The courses were taught simultaneously in four different ... -
Activity modelling in a collaborative ceramic tile design chain: an enhanced IDEF0 approach
Springer-Verlag (2008)Explicit descriptions of should-be and to-be activities and processes are key elements in implementing industrial projects aimed at improving new-product development (NPD) processes, especially when e-collaboration utilities ... -
Actuator Fault Tolerant Control Proposal for PI Controlled SISO Systems
Elsevier (2018-08-29)In this work, we develop a control structure which can be added to an existing closed loop in order to mitigate the effect of actuator faults. We analyze the initial performance of the closed loop in terms of robustness ... -
Adaptive control optimization in micro-milling of hardened steels-evaluation of optimization approaches
Springer (2016-06)Nowadays, the miniaturization of many consumer products is extending the use of micro-milling operations with high-quality requirements. However, the impacts of cutting-tool wear on part dimensions, form and surface integrity ... -
Adhesion enhancement of powder coatings on galvanised steel by addition of organo-modified silica particles
Elsevier (2014-08)The addition of organo-modified silica particles (OSP) to organic monolayer coatings has been investigated as an alternative to the use of primers or surface pretreatments in galvanised steel substrates. A commercial ... -
Admittance study of grid-connected VSCs for harmonic oscillatory instabilities
IET (2019-07)Voltage source converters (VSCs) can reduce damping of grid-connected VSC systems at harmonic resonances, leading to system instability. The conductance of the VSC admittance can be shaped selecting appropriate VSC parameter ... -
Aeronautical ground lighting system study: field measurements and simulations
Institution of Engineering and Technology (IET) (2016)Aeronautical ground lighting (AGL) systems are single-phase series circuits where constant current regulators supply transformers and luminaires. These systems provide visual reference to aircraft during airport operations. ... -
An approach to conceptual and embodiment design within a new product development lifecycle framework
Taylor & Francis (2016)The design of new innovative products is the result of an accurate and precise management of knowledge sources all over its life cycle, such as technology, market, competitors and suppliers. The work contributes with a ... -
An experimental study of process variables in turning operations of Ti–6Al–4V and Cr–Co spherical prostheses
Springer Verlag (2012)Ti–6Al–4V and Cr–Co alloys are extensively used in manufacturing prostheses due to their biocompatibility, high strength-to-weight ratio and high resistance to corrosion and wear. However, machining operations involving ... -
An investigation into alternative conceptions and knowledge retention of manufacturing concepts in undergraduate/graduate engineering students
Elsevier (2013)Manufacturing organizations are constantly demanding competent young engineers with a solid knowledge on manufacturing topics. At Engineering Degrees, Manufacturing Processes is a compulsory subject where the students learn ... -
An ontology for integrated machining and inspection process planning focusing on resource capabilities
Taylor & Francis (2016)The search for and assignment of resources is extremely important for the efficient planning of any process in a distributed environment, such as the Collaborative Product Integrated Development process. These environments ...