Listar Departament: Enginyeria de Sistemes Industrials i Disseny por autoría "d2f7080c-118c-48d8-a439-7d16b136e153"
Mostrando ítems 1-7 de 7
-
Analysis of the hardness ratio effect on the tribological performance of NiCrBSi coating/debris particles using the Stribeck Curve
Habib Ameen, Kudama; Leal Cano, David; Heredia Álvaro, José Antonio; Serrano Mira, Julio Elsevier (2021-12-15)This work aims to propose an approach to estimate the final surface roughness as a function of the hardness ratio between coating and debris (Hpin/Hdebris = Hp/Hd) under lubricated conditions employing pin-on-disc ... -
Effect of debris size on the tribological performance of thermally sprayed coatings
Habib Ameen, Kudama; Leal Cano, David; Heredia Álvaro, José Antonio; Vicente-Escuder, Angel Elsevier (2020)This research aims to assess the effect of the debris particle size on the tribological performance and lubrication regime parameters of a Ni-based alloy coating. This is a key industrial problem, and its resolution can ... -
Effects of thermal spraying technique on the remelting behavior of NiCrBSi coatings
Habib Ameen, Kudama; Leal Cano, David; Heredia Álvaro, José Antonio; Serrano Mira, Julio; Llopis, Rodrigo; López Moreno, D.; Mohammed, Samar S. Elsevier (2022)This study aims to understand and quantify the influence of the deposition technique on the remelting parameters, microstructure, microhardness, and abrasive behavior of NiCrBSi coatings. An experimental study was conducted ... -
Impact of Microstructure on Remelting Parameters and Mechanical Behavior of Thermally Sprayed NiCrBSi Coating
Habib Ameen, Kudama; Leal Cano, David; Serrano Mira, Julio; RAYÓN ENCINAS, EMILIO; Dosta, Sergi Springer (2023-11-20)The present study concerns controlling and quantifying the impact of the remelting thermos-cycle curve parameters on the microstructure evolution and mechanical properties of remelted NiCrBSi coatings. This coating was ... -
Impacto de la adición de AI2O3 sobre la estabilidad de los regímenes de lubricación de recubrimientos de base níquel depositados por proyección térmica (OF) y refundidos por llama
Leal Cano, David; Habib Ameen, Kudama; Rayón, Emilio UNED - Universidad Nacional de Educación a Distancia (2023)Este trabajo tiene como objeto estudiar la influencia de las adiciones del 10% de Al 2O3 micrométrica en recubrimien- tos de NiCrBSi (10.1% y 15.25% Cr) y NiCrBSi/WC (60/40%, 15.25% Cr) depositados mediante proyección ... -
Influence of Al2O3 Particle Size on Microstructure, Mechanical Properties and Abrasive Wear Behavior of Flame-Sprayed and Remelted NiCrBSi Coatings
Habib Ameen, Kudama; Leal Cano, David; Tarazona Caudet, C.; Sharif Damra, Mohammad; Cervera González, Iván; Bellés Bellés, Joan; Ortells, P. Springer Verlag (2017-03)The influence of micrometric alumina (low surface area-to-volume ratio) and nanometric alumina (high surface area-to-volume ratio) on microstructure, hardness and abrasive wear of a NiCrBSi hardfacing alloy coating applied ... -
Investigación en la influencia del contenido en Cr de aleaciones NiCrBSi sobre el par rozante Acero F-5220 templado en aceite en la modelización del comportamiento tribológico en medios lubricados. (Curva de Stribeck)
Leal Cano, David; Habib Ameen, Kudama; Tarazona Caudet, C.; Ortelles, P. Universidad Miguel Hernández de Elche. Grupo de Ingeniería Mecánica Aplicada (AME) (2016)Se han escogido los recubrimientos NiCrBSi debido a sus características mecánicas que los hacen ser materiales adecuados para ser utilizados contra el desgaste abrasivo, erosión, cavitación, etc. en diversas aplicaciones, ...