Listar Institut Universitari de Tecnologia Ceràmica "Agustín Escardino" (ITC) por título
-
Engineering zirconia coating microstructures by using saccharides in aqueous suspension plasma spraying feedstocks
Elsevier (2020-10-15)This study aims to demonstrate the feasibility to develop columnar microstructures in zirconia coatings manufactured by suspension plasma spray, through the modification of the properties of the suspension feedstocks with ... -
Enhanced Atenolol oxidation by ferrites photoanodes grown on ceramic SnO2-Sb2O3 anodes
Elsevier (2022-03-24)The increase in the consumption of pharmaceutical compounds has caused the increment of their presence in different body waters. β-blockers are one of the most dangerous even at low concentrations (ng L−1). Anodic oxidation ... -
Environmental profile of Spanish porcelain stoneware tiles
Springer (2018-08)Purpose Porcelain stoneware tile (PST) iscurrently the ceram- ic tile of greatest commercial and innovation interest. An envi- ronmental life cycle assessment of different varieties of PST was undertaken to enable ... -
Estimación de la huella hídrica de baldosas de gres porcelánico esmaltado
Sociedad Española de Cerámica y Vidrio (2013)En este trabajo se presenta un primer estudio de la estimación de la huella hídrica de las baldosas de gres porcelánico esmaltado, realizado a partir de datos sectoriales, es decir, no es un estudio específico de ninguna ... -
Feasibility of incorporating silica aerogel in atmospheric plasma spraying coatings
Elsevier (2021-06-07)This study aims to demonstrate the feasibility of developing zirconia ceramic coatings with the incorporation of silica aerogel particles, which exhibit outstanding insulating properties. Thus, the research aims to find a ... -
Feasibility of using organosilane dry-coated detoxified quartzes as raw material in different industrial sectors
Elsevier (2021-11-10)Respirable crystalline silica (RCS), in the form of quartz and cristobalite from occupational sources, was classified by the International Agency for Research on Cancer (IARC) as carcinogenic to humans (category 1). In ... -
Glass with a low-melting temperature belonging to the P2O5–CaO–Na2O system, applied as a coating on technical ceramics (alumina, zirconia) and traditional ceramics (porcelain stoneware)
Sociedad Española de Cerámica y Vidrio (2024-03)This article investigates the development and potential applications of low-melting point lead-free glasses. Their importance is due to strong market demands to comply with the strict international regulations against the ... -
Grain coarsening during liquid phase sintering of zircon-glass composites
Elsevier (2023-08-09)This study examined zircon grain growth during isothermal sintering of a zircon-glass composite with a zircon volume fraction of 0.525 zircon volume/solids volume, at a temperature of 1200 degrees C, with different residence ... -
How can the European ceramic tile industry meet the EU's low-carbon targets? A life cycle perspective
Elsevier (2018-07)Ceramic tile manufacturing is deemed to be an energy intensive industry, mainly based on combustion processes and, therefore, subject to European policies aiming at reducing greenhouse gas emissions. The “Roadmap for moving ... -
Improvement of salicylic acid biological effect through its encapsulation with silica or chitosan
Elsevier B.V. (2021-12-30)Attacks of necrotrophic and biotrophic fungi affect a large number of crops worldwide and are difficult to control with fungicides due to their genetic plasticity. Encapsulation technology is a good alternative for ... -
In operando characterization of the ionic conductivity dependence on liquid transient phase and microstructure of cold-sintered Bi2O3-doped Li1.3Al0.3Ti1.7(PO4)3 solid-state electrolyte
Elsevier (2023-08-31)A disruptive sintering technique, Cold Sintering Process (CSP), has been used to produce cold-sintered samples of Bi2O3-doped Li1.3Al0.3Ti1.7(PO4)3 (LATP) as solid-state electrolyte (SSE). An in operando impedance study ... -
Industry-scalable wall tile composition based on circular economy
Sociedad Española de Cerámica y Vidrio (2022-08)En el marco de la economía circular y la valorización de residuos, el presente trabajo aborda la posibilidad de fabricar azulejos cuyos soportes incluyan residuos en su formulación. Los residuos seleccionados son tiesto ... -
Influence of microstructure and magnetizing mechanisms on magnetic complex permeability (imaginary part) of a Cu-doped Ni-Zn polycrystalline ferrite
Elsevier (2021)The complex permeability of the Cu-doped Ni–Zn polycrystalline ferrites is strongly dependent on microstructure, particularly on relative density (ϕ) and average grain size (G), as it has been shown in a previous ... -
Influence of solids concentration on the microstructure of suspension plasma sprayed Y-TZP/Al2O3/SiC composite coatings
Elsevier (2019)The present research focuses on the effect of feedstock suspension solid concentration on the microstructure of suspension plasma sprayed Y-TZP/Al2O3/SiC composite coatings. For this purpose, concentrated aqueous suspensions ... -
Influence of the molecular weight of carboxymethylcellulose on properties of Binder Jetting manufactured parts
Elsevier ScienceDirect (2022-06-15)The influence of the molecular weight of carboxymethylcellulose as solid binder for additive manufacturing was studied. Three sodium carboxymethyl celluloses with different molecular weights were added to a stoneware. The ... -
Ink-jet technology applied to engineer low-cost ceramic membranes
Universitat Politècnica de València. Research Institute for Industrial, Radiophysical and Environmental Safety (ISIRYM). Prometeo Research Group (Membrane Processes and Environmental Effluent Treatment) (2018-07-09)This contribution analyses the suitability of the ceramic ink-jet technology to apply layers over a porous ceramic support, as the basis for a development of a standardized method to synthesize multilayer ceramic membranes. -
Inkjet technology for ceramic products. Influence of some process variables on ink penetration
Wiley (2019-07-27)Inkjet technology has become very popular in recent years and is nowadays widely used for decorating ceramic products. This has led to in-depth study of the operating principles and process variables involved. These ... -
Introducing an ionic conductive matrix to the cold-sintered Li1.3Al0.3Ti1.7(PO4)3-based composite solid electrolyte to enhance the electrical properties
Elsevier (2023-08-09)In the present work, a Polymer-In-Ceramics (PIC) solid electrolyte based on Li1.3Al0.3Ti1.7(PO4)3 (LATP) and PEOn-LiTFSI (poly(ethylene oxide) - lithium bis(trifluoromethanesulfonyl)imide) is obtained via Cold Sintering ... -
KATCH_e: Training materials and tools for circular economy in practice
Institute for Sustainability Science and Technology , Universitat Politècnica de Catalunya (2019-10-15)KATCH_e is a knowledge alliance between research centres, universities and companies to build competences in the field of product-service development for the circular economy and sustainability. This ERASMUS + funded project ... -
Kinetics of the transformations occurring during the firing process of an industrial spray-dried porcelain stoneware body
Elsevier (2022-03-08)Pressed compacts of an industrial spray-dried porcelain stoneware powder, consisting mainly of albite, quartz, kaolinite, and illite, were thermally treated at different temperatures and times. Fired test piece bulk density ...